Forks - Wheels - Tires - All Listings
livepages::jquery();?>All Listings > Forks - Wheels - Tires
Categories: |
Products In This Category: |
( 19 ) Old School Springer BLACK powder coated with CHROME springs - £987.301" neck post and measures approximately 19" from top of the bottom yoke down to wheel axle centre.......a 21" is also listed( 21 ) Old School Springer BLACK powder coated with CHROME springs - £1098.001" neck post and measure approximately 21" from top of the bottom yoke down to wheel axle centre.......21" is available by request.143mm Frame Headstock ( Supplied with MATCHED cups ) Steering neck Bobber Chopper Harley type MACHINED + Chr cups + Taper Bearings - £114.78Ideal for fitting our listed custom springers or any Harley replacement 1" neck post type forks into your existing frame or for a complete ground up frame build.143mm Frame Headstock * NO CUPS SUPPLIED * ( MACHINED For MATCHED cups ) Steering neck Bobber Chopper Harley type MACHINED + Taper Bearings - £88.23Ideal for fitting our listed custom springers or any Harley replacement 1" neck post type forks into your existing frame or for a complete ground up frame build.1x Wheel Spindle machined for 3/4" for SOLID Axle Plate Use up to 20cm. Measurement ( A ) in drawing. Chopper Bobber Harley - £48.67This is the minimum width measured from the outside of your compressed axle plates/swingarm. Made from EN19T steel and threaded for 5/8" UNF chrome Acorn nuts and stainless steel washers. NOT for HOLLOW sectional use.1x Wheel Spindle machined for 3/4" for SOLID Axle Plate Use up to 30cm. Measurement ( A ) in drawing. Chopper Bobber Harley - £56.32This is the minimum width measured from the outside of your compressed axle plates/swingarm. Made from EN19T steel and threaded for 5/8" UNF chrome Acorn nuts and stainless steel washers. NOT for HOLLOW sectional use.1x Wheel Spindle machined for 3/4" for SOLID Axle Plate Use up to 40cm. Measurement ( A ) in drawing. Chopper Bobber Harley - £64.63This is the minimum width measured from the outside of your compressed axle plates/swingarm. Made from EN19T steel & threaded for 5/8" UNF chrome Acorn nuts and stainless steel washers. NOT for HOLLOW sectional axle holding use. FULL contact area required2 x Bearings & Outer Races for Headstock *GENUINE TIMKEN* for Harley Davidson forks Bobber Choppers Cycle Haven - £37.342 x bearings & 2 x outer races (Order 1 for complete build..content as photo) Fit Harley models at least from 1960 thru to 2011 and some as early as 1949 Using 1" inside diameter bearings & inside diameter bearings & 50.30mm outside diameter races21" x 2.15 CHROME 40 spoke SINGLE disc NARROW hub Front Wheel 3/4" axle FX & XL 78-83 - £296.22Uses OEM mounting hardware; designed to use OEM style rotors, pulleys and sprockets Fully assembled and trued with bearings installed and end play set Polished and chrome-plated billet aluminum hub.. Last priced 8/2026" 120/50x26 Vee Rubber inner tube for Harley Chopper Bobber Trike. TR-4 metal center valve - £39.16. Vee Rubber tires are Tubeless but can be used as tube type tire too. Vee Rubber tires are "E" and DOT approved.3/4" Axle reducer... BUSHING TO INSERT INTO 1" axle sized Harley wheel bearings - £11.12Sold in pairs ( Cheap imports )3/4" Wheel axle adapter / reducer ( 1 Pair ) made in S/S to your dimensions for 1" bearings on Harley Davidson models... Cycle Haven - £60.00SOLD IN PAIRS... allows the use of the later 1" axle bearing type wheels on older 3/4" axles.30 - 41mm O.D. Fork Tube Extensions Chopper Bobber or Metric Cruiser & Custom & Cafe Racers needing extra ground clearance *SOLD IN PAIRS* - £158.00Made from solid Stainless Steel in 2 - 4 - 6 inch lengths.. Please supply your fork tubes as instucted via More Information.35mm + 2" Overstock Fork Tube Stanchions for Harley Davidson 75 to 83 Sportsters & 76-83 FX B/T models for Chopper Bobber Custom..* SOLD IN PAIRS * - £247.68Chrome Plated Finish ... These are 25 3/16" in length.... other lenghts & models to order35mm + 4" Overstock Fork Tube Stanchions for Harley Davidson 84-86 Sportsters & FX B/T models for Chopper Bobber Custom..* SOLD IN PAIRS * - £272.3584-85 FX : 84-86 FXR : 83-86 FXRD FXRT : 84-85 FXSB : 85-86 FXRS ** OTHER LENGTHS AVAILABLE ** by request. Last priced 7/2036mm x 32" length 26mm I.D. show chromed 17mm for damper valve shafts, Overstock Fork Tubes From OUR shop stock Chopper Bobber Metric Cruiser Yamaha - £197.12* SOLD in PAIRS * Show Chrome plated.... 26mm I.D. for damper pistons swept area Other makes and models available From £172.68 .... |